Studebaker E-series truck

History

The most distinctive characteristic of Studebaker E-series trucks is the cab, which remained unchanged through the 1959 models. With only two changes - a one-piece windshield in 1954 (for the preceding 3R series) and a larger rear window in 1955 for the first E series – it was essentially the same cab as was introduced on the 2R series in mid-1948 as a 1949 model. The first E was available with three engines, the Champion 185 cuin inline-six with 92 hp, the Commander 246 cuin six with 102 hp, or the 224 cuin Commander V8 with 140 hp. The heavier 1½ and 2 ton models were available with the bigger 259 cuin Commander V8, with 156 or respectively. The bigger engines gradually migrated into the lighter offerings over the years, with the six-cylinder models becoming ever less relevant. In 1957 Studebaker's 289 cuin V8 engine found its way into the heavy duty 2-ton 3E40 and was sporadically available, mostly at the top of the weight range.

The 1956 2E received a new hood, with the "Studebaker" script now on a secondary chrome grille mounted up high. The front turn signals were also incorporated in the grille, beneath the headlights. 20,218 Studebaker 2E trucks were built in the 1956 model year. A new massive fiberglass grille appeared on the 1957-58 3E models, and was the last significant styling change made to these trucks.

For the 1958 and 59 model years, a stripped-down, low-cost Studebaker truck, called the Scotsman, was produced in addition to the Transtars, in 1/2 and 3/4-ton ratings. To save money, it used a modified version of the 1949-53 grille and was spartan in almost every way. For unknown reasons, the Transtar name was dropped from the Studebaker truck line in 1959, though it reappeared in 1960 on the 1-, 1½-, and 2-ton models.

For 1960, E-series trucks received their only major restyling. Called the Champ, the design used the front panels from the 1959–1960 Studebaker Lark passenger car and was available in 1/2-ton and 3/4-ton models.

The 1/2, 3/4, and 1-ton trucks were generally available with both 6-cylinder and V8 engines (no six-cylinder engines were available in the 1-ton trucks after 1960). Larger trucks came with V8s only. Beginning with the 1962 7E models, a 130 hp 212 cuin Detroit Diesel engine was also available in those of 1-ton or above capacity, and air brakes could be had on 2-ton models. A "96BBC" (meaning 96 inches from bumper to back of cab) was available in both gasoline- and diesel-powered models beginning in 1962. The short cab length was achieved by deleting the fiberglass grille, flattening the front of the hood, and applying a very distinctive flat nose below the hood. This model was produced in response to some state laws that restricted the overall length of tractor trailers, and thus permitted the use of longer trailers. In the last two model years a 97 hp 159 cuin three-cylinder Detroit Diesel 3D-53 engine was offered in 1 and 1½-ton configurations (8E15 and 8E25). Production of diesel-engined models was very low, although they continued to be available until the end in 1964.

Four-wheel drive was available on 1/2 and 3/4-ton models beginning in 1957. Studebaker did not make the 4WD equipment themselves, but (in common with Chevrolet and GMC at the time) purchased the hardware from NAPCO (Northwestern Auto Parts Company).

References

References

1. Lackie, Skip. "Studebaker Truck Model Designations and Data (Appendix A)". Studebaker Drivers Club.
2. "1956 Studebaker Transtar trucks". Classic Automobile Appraisal And Resource Guide.
3. Lackie, Skip. "A Brief History of Studebaker Trucks: An Analysis of Production Records". Studebaker Drivers Club.