Hot work

Types of hot work

Welding

The process of joining two pieces of metal or plastic together through an electrode. Several forms of welding exist, including:

• Shielded Metal Arc Welding (SMAW) or Stick Welding
• Gas Metal Arc Welding (GMAW) or Magnesium Inert Gas Welding (MIG)
• Flux-Cored Arc Welding (FCAW)
• Gas Tungsten Arc Welding (GTAW) or Tungsten Inert Gas Welding (TIG)
• Submerged Arc Welding (SAW)

Welding temperatures vary depending on the type of electrode, but is typically higher than soldering.

Soldering

Soldering is the same type of joining process as welding but uses different filler material called solder and operates at under 450 degrees Celsius (841 degrees Fahrenheit). Soldering is commonly used in circuit boards and copper pipes in plumbing.

Brazing

Brazing is used in applications to join close fitting members in the range of 0.001 to 0.005 inches. Brazing operations are conducted at temperatures above 450 degrees Celsius.

Cutting

Cutting processes that produce sparks fall under the category of hot work. Examples include sparks produced from saw cutting and grinding.

Safety

• Hazard assessment: Identify fire, explosion, and environmental risks in the work area.
• Hot work permitting: Complete the hot work permitting process ensuing that all items are filled out and accounted for.
  • Special considerations and additional safety measures should be made if hot work is required in a confined space.
• Area preparation: Remove or protect combustibles, ensure ventilation, and inspect equipment.
• Fire watch: Designate an individual(s) to be present during the work and after to monitor for fires or other hazards.

While hot work is inherently hazardous, using the methods listed above along with the hierarchy of controls is widely recognized as a best practice for maintaining safety during these types of activities.

Fire watch

Fire watch is a short-term safety work practice that involves one or more individuals continuously monitoring a building, or a specific area within it, to detect and address fire hazards during hot work operations or during periods of life safety system impairments.

During hot work activities, fire watch is intended to ensure that hot work byproducts (sparks, slag, metal, etc.) do not affect the surrounding workplace or spread to other areas. Fire watch duties must be carried out by at least two individuals. In the United States, OSHA specifies that the person performing the hot work cannot also serve as the fire watch.

Fire watch duties include:

• Have access to least one fire extinguisher and being trained in its proper use. In occupied buildings, this extinguisher should not be removed from its designated location or surrounding areas. This extinguisher should specially be for hot work activities.
  • The fire extinguisher should be rated at a minimum of 2-A:20-B:C and located within 30 feet of the hot work activities.
  • Fire extinguisher operation: P.A.S.S - Pull the pin, Aim the nozzle as base of fire, Squeeze handle firmly, Sweep the area affected area.
• Patrol the immediate and surrounding area for signs of fire or any other possible hazard.
• Sound the alarm in the event there is a fire or emergency. Fire watch personnel should have an effective way to communicate with other individuals in the work place and a reliable way to get in touch with emergency services.
• Maintain the fire watch for the entire duration of hot work activates and for at least 30 minutes after the completion of all work.
  • Depending on the authority having jurisdiction, the duration of the fire watch may be extended based on the specific hazards associated with the hot work or the surrounding environment.

Hot work permit

When referring to widely recognized regulatory guidance such as National Fire Protection Agency (NFPA) 51B: Standard for Fire Prevention During Welding, Cutting, and Other Hot Work and the International Fire Code (IFC) Chapter 35: Welding and Other Hot Work, this permitting process is required to be completed before any hot work can begin.

Steps in the hot work permitting process:

1. The hot work operator conducts a risk assessment of the intended work area.
2. The operator gathers all appropriate equipment and safety items.
3. A fire watch is designated to monitor the area during and after the work.
4. The operator completes the permit recording all information and confirming that all safety measures have been addressed.
5. The permit is submitted for approval to a supervisor or designated authorizing individual(s).
6. Once approved, the permit must be visibly posted at the hot work site for the entire duration of the work.
7. After all hot work is completed, the permit must be retained for at least three years to comply with regulatory requirements and to support audits or incident investigations.

Confined spaces

• Limited access points make entering and exiting difficult
• Poor ventilation and limited airflow can lead to the buildup of toxic and flammable gasses
• Gasses such as Carbon Monoxide can buildup from hot work in confined spaces
• Workers can face entrapment when physical barriers or equipment fails

In the united states, OSHA requires confined spaces where hot work is done to acquire a permit for hot work. General requirements for hot work include:

• The employer shall post danger signs or other effective means of the existence, location, and danger posed by permit spaces
• The employer must have a written permit confined space program available for inspection by employees

There are several specific circumstances in which an employer may qualify for exemptions from parts of the regulation, such as when the hazard present is solely a hazardous atmosphere and forced ventilation is utilized.

International standards and adoption of hot work safety practices

Most countries in the world use their own rules and regulations that have different responsibilities for both the employer and employee regarding safety and risk mitigation in the workplace, while some countries lack these rules or struggle to enforce them. The International Fire Code Chapter 35 presents a general framework for countries to adopt and utilize in the building of their own safety regulations regarding hot work.

Agencies, governments, and/or safety organizations that have adopted some version of hot work safety practices

• United States – Occupational Safety and Health Administration: OSHA 1910 Subpart Q (General Industry), 1915 Subpart D (Shipyard), 1917 Subpart G (Marie Terminals), 1926 Subpart J (Construction)
• Europe – Confederation of Fire Protection Associations Europe: CFPA-E Guideline No 12:2023 F (Fire Safety Basics for Hot Work Operatives)
• United Kingdom – The Regulatory Reform (Fire Safety) Order 2005: Part 2 Fire Safety Duties
• Singapore – Workplace Safety and Health (Shipbuilding and Ship-Repairing) Regulations: Part V Hot Work Permit System
• Russia – Order No. 1479 Rules of fire prevention regime in the Russian Federation
• World Wide / International – National Fire Protection Agency: Standard for Fire Prevention During Welding, Cutting, and Other Hot Work, International Fire Code: Chapter 35 - Welding & Other Hot Work, NIST: Fire Prevention During Welding, Cutting, and Other Hot Work

References

References

1. Burgess, Holly. (2023-10-06). "Hot Work: More than Welding, Cutting, and Burning".
2. "29 CFR Part 1910 Subpart Q -- Welding, Cutting and Brazing".
3. "Fire Watch Duties during Hot Work".
4. "Welding 101: A Supervisor's Guide".
5. (2004). "Principles of Soldering". ASM International.
6. (2014-02-27). "Understanding Brazing Fundamentals".
7. (June 2010). "Temperature variations and spark generations from rock contact in hot saws".
8. (2019). "From the microstructure of steels to the explosion of sparks". Emergent Scientist.
9. Rudilosso, Frank D.. (2020-10-19). "Defining a fire watch for NFPA compliance {{!}} HFM Magazine".
10. "Fire Watch Duties during Hot Work".
11. "Chapter 35 Welding and Other Hot Work – 2024 International Fire Code (IFC) Section 3504.2.6 Fire Extinguisher".
12. "Choosing and Using Fire Extinguishers".
13. "Chapter 35 Welding and Other Hot Work – 2024 International Fire Code (IFC) Section 3504.2.1 When Required".
14. productioneditor. (2024-10-23). "Improving worker safety in confined space entry and hot work operations: Best practices for high-risk industries".
15. "Confined Spaces".
16. "1910.146 - Permit-required confined spaces".
17. "Chapter 35 Welding and Other Hot Work – 2021 International Fire Code (IFC)".
18. "1910 Subpart Q: Welding, Cutting and Brazing".
19. "OSHA 1915 Subpart D - Welding, Cutting and Heating".
20. "OSHA 1917 Subpart G: Related Terminal Operations and Equipment".
21. "1926 Subpart J - Welding and Cutting".
22. (January 2023). "The Confederation of Fire Protection Associations Europe: Fire safety basics for hot work operatives".
23. "The Regulatory Reform (Fire Safety) Order 2005: Part 2 Fire Safety Duties".
24. "Workplace Safety and Health (Shipbuilding and Ship-Repairing) Regulations 2008 - Singapore Statutes Online".
25. "Order of the Government of the Russian Federation "About Approval of Rules of Fire Prevention Regime in the Russian Federation"".
26. "NFPA 51B Standard Development".
27. "Chapter 35 Welding and Other Hot Work – 2024 International Fire Code (IFC)".
28. "National Institute of Standards & Technology: Fire Prevention During Welding, Cutting, and Other Hot Work".